Maria Elena Manzor D.D.S., P.C.
28633 Hoover
Warren, MI 48093

(586) 751-3950
Fax (586) 751-3992

Posts for: October, 2019

By Maria Elena Manzor D.D.S., P.C.
October 25, 2019
Category: Dental Procedures
Tags: crown  
AStainlessSteelCrownCouldExtendtheLifeofaPrimaryMolar

One of the key elements in a child’s development is their first set of teeth. Although primary (“baby”) teeth last only a few years, they’re critically important for enabling a child to eat solid foods, speak and smile.

But they also provide one more important benefit—they hold the space in the jaw reserved for the permanent teeth developing just under the gums until they erupt. But if a child loses a primary tooth prematurely because of disease or injury, other teeth may drift into the vacant space and crowd it out for the intended permanent tooth. It may then come in misaligned or remain stuck within the gums (impaction).

To avoid this, we try to treat and preserve a diseased primary tooth if at all practical. For a primary molar, one of the large teeth in the back of the mouth, this might include capping it with a stainless steel crown.

Why a metal crown? Primary molars normally don’t fall out until around ages 10-12, so it may be years for a younger child before their permanent molars erupt. All during that time these particular teeth will encounter heavier biting forces than teeth in the front.

A steel crown is often the best solution for a molar given their longer lifespans and encountered biting forces. The crown’s metal construction can stand up to these forces while still protecting the tooth from re-infection from decay. And because molars are typically outside of the “smile zone” occupied by more visible front teeth, the crown’s metal appearance isn’t usually an aesthetic issue.

Crowning a molar usually takes one visit, a dentist typically performing the procedure with local anesthesia and possibly a mild sedative like nitrous oxide gas (“laughing gas”). After removing any decayed structure from the tooth, the dentist will then fit a pre-formed crown over the remaining structure, sized and shaped to match the original tooth as close as possible.

A stainless steel crown is a cost-effective way to added needed years to a primary molar that could otherwise be lost prematurely. Preserving it may help a child avoid bite problems and expensive future treatments.

If you would like more information on dental care for primary teeth, please contact us or schedule an appointment for a consultation. You can also learn more about this topic by reading the Dear Doctor magazine article “Stainless Steel Crowns for Kids: A Safe and Effective Way to Restore Primary Molars.”


By Maria Elena Manzor D.D.S., P.C.
October 15, 2019
Category: Dental Procedures
Tags: dental implants   dentures  
Implant-SupportedDenturesCouldContributetoBetterBoneHealth

For generations, dentures have helped people avoid the dire consequences of total teeth loss. Now, implant technology is making them even better.

Composed of life-like prosthetic teeth fixed within a plastic or resin gum-colored base, dentures are manufactured to fit an individual patient’s mouth for maximum fit, comfort and performance. But dentures also have a critical drawback—they can’t stop bone loss in the jaw.

Bone is constantly regenerating as older cells dissolve and then are replaced by newer cells. In the jawbone, the forces generated when we chew travel through the teeth to the bone and help stimulate this new cell growth. When teeth are missing, though, the bone doesn’t receive this stimulus and may not regenerate at a healthy rate, resulting in gradual bone loss.

Dentures can’t transmit this chewing stimulus to the bone. In fact, the pressure they produce as they rest on top of the gums may actually accelerate bone loss. Over time then, a denture’s once secure and comfortable fit becomes loose.

In the past, most patients with loose dentures have had them relined with new dental material to improve fit, or have new dentures created to conform to the changed contours of the jaws. But implant technology now offers another alternative.

Implants are in essence a tooth root replacement. Dentists surgically implant a titanium metal post directly into the jawbone that naturally attracts bone cells to grow and adhere to it over time (a process called osseointegration). This not only creates a secure and lasting hold, it can also stop or even reverse bone loss.

Most people know implants as single tooth replacements with a porcelain crown attached to the titanium post. But a few strategically placed implants can also support either removable or fixed dentures. Removable dentures (also called overdentures) usually need only 3 or 4 implants on the top jaw and 2 on the bottom jaw for support through built-in connectors in the dentures that attach to the implants. A fixed bridge may require 4-6 implants to which they are permanently attached.

There are pros and cons for each of these options and they’re both more expensive than traditional dentures. In the long run, though, implant-supported dentures could be more beneficial for your bone health and hold their fit longer.

If you would like more information on implant-supported dental work, please contact us or schedule an appointment for a consultation.


By Maria Elena Manzor D.D.S., P.C.
October 05, 2019
Category: Uncategorized
Tags: dental implant  
TheDigitalRevolutionIsTransformingImplantTherapy

Compared to other dental restorations—a few of which have been around for over a century—implants are a relatively recent development. But even though it's just now entering its fourth decade, recent advances have catapulted implant therapy well beyond where it began.

That's due mainly to digital technology. Two examples of this, computed tomography (CT) and 3-D printing, are increasing the accuracy and efficiency of implant placement.

Properly placing an implant is one of the most important elements in achieving a natural and attractive result. But finding the best location is often difficult due to a lack of suitable bone volume, the patient's bite or the proximity of anatomical structures like nerves and blood vessels. CT imaging, especially Cone Beam CT scanners (CBCT), is helping to make implant placement planning easier.

Unlike the static, two-dimensional views of standard x-rays, CBCT takes hundreds of images and digitally blends them together to create a virtual 3-D model of the patient's jaw and face. Dentists can view this highly detailed model on a computer monitor from various vantage points and better identify possible obstructions. With better information about what "lies beneath," they can more accurately pinpoint the best implant site.

Creating the ideal plan is one thing—successfully implementing it is another. Dentists often create a surgical guide that helps them drill in precisely the right positions during surgery. The guide, which resembles a mouthguard, fits over the gums and contains marker locations for drilling.

Many dentists are now using 3-D printing to create these surgical guides. A 3-D printer turns a digital model of the guide based on measurements of the patient's mouth and proposed implant locations into an actual physical object "printed out" layer by layer of special polymer material. The end product can be more precise than guides created by other means.

These and other technological developments are helping implant therapy rise to a new level of success. With the resulting increase in accuracy, efficiency and less treatment time, tomorrow's implant patients will be the ultimate beneficiaries.

If you would like more information on restoring missing teeth with dental implants, please contact us or schedule an appointment for a consultation. You can also learn more about this topic by reading the Dear Doctor magazine article “How Technology Aids Dental Implant Therapy.”




Contact Us

Maria Elena Manzor D.D.S., P.C.

(586) 751-3950
Fax (586) 751-3992

28633 Hoover Rd Warren, MI 48093